ATTACHMENTS FOR SAFE PILE CUTTING

Use MotoCut products to improve safety, productivity and quality of pile cutting.

STEEL PILE CUTTING

  • Significantly increases operational job safety
  • Safe pile handling, operator isolated from the danger zone
  • Eliminates the risk of injuries from falling piles
  • Prevents all hand-arm vibration (HAVS) issues
  • Operator not exposed to fumes and metal particles

  • Fully self-contained add-on for any 14–30 ton hydraulic excavator equipped with hammer line and tiltrotator
  • Built-in 20kW/400V hydraulic electric generator, 400 l/min (14 C.F.M.) air compressor and 85A/400V plasma generator
  • Expensive combustible gases, such as oxygen or acetylene not required
  • Low operating costs – contactless plasma cutting process that only uses fuel from the excavator
  • High productivity, up to 150 pile cuts per day
  • Excellent quality cuts, cut-offs can be reused and easily welded together
 

  • Tiltrotator for rotating and tilting the pile cutter
  • Remote diagnostics to detect faults and monitor selected parameters
  • Level for aligning the pile cutter
  • Video assisted pile alignment
  • 2D or 3D measuring system for automatical detection of pile cutting height
  • Air supply for air tools, etc.
  • Option to plug in a handheld plasma unit up to 20 m (60’) away
  • Customized MotoCut pile cutters

REQUIREMENTS

  • Tiltrotator
  • 24V (or 12V + converter)
  • Free auxiliary hydraulic circuit (Hammer line)
  • Hoses for the grapples (extra lines from Tiltrotator)

BENEFITS

• Zero Waste piling
• High quality and predictable cutting results
• Easy to attach to an excavator and transport to the worksite
• Accelerates worksite schedules
• Allows placing the cut-offs to desired location for easy removal
• Can be attached to 14-30 ton excavators

DOWNLOAD BROCHURE

CONCRETE PILE CUTTING

MotoCut Pile Cutter can be attached to any min 5 tn excavator from where it gets the hydraulic power. It operates with two fast rotating diamond blades. The cutting device is maneuvered from the cabin of the excavator thus there is no need to hazardous hand work nearby the pile. The MotoCut Pile Cutter replaces manual labour in physically heavy pile cutting work, making the job even five times faster and most importantly with minimized risk of accidents – SAFETY FIRST!

  • Operator isolated from the danger zone
  • No risk of cut piles falling on operators
  • No HAVS issues (Hand-Arm Vibration Syndrome)
  • No Silica dust issues
  • Up to 5x higher production capacity compared to traditional methods
  • High quality and predictable cutting result
  • Easy to transport to the work site and attach to an excavator
  • Speeds up the site schedules

  • Tiltrotator for rotating and tilting the pile cutter
  • Remote diagnostics to detect faults and monitor selected parameters
  • Level for aligning the pile cutter
  • Video assisted pile alignment
  • 2D or 3D measuring system for automatical detection of pile cutting height
  • Air supply for air tools, etc.
  • Option to plug in a handheld plasma unit up to 20 m (60’) away
  • Customized MotoCut pile cutters

CUT & BREAK PILE CUTTERS

The pile cutter is fully self-contained and works with any 5-30 ton hydraulic excavator with a hammer line and tiltrotator or the MotoCut free hanging chain set. With 2 blades cutting simultaneously, the cutting speed is typically up to 5x faster than in manual cutting.

  • Grab the pile, press Start and wait until the rebars are cut
  • Retract the grapples and grab the pile from a higher point
  • Break the pile and place the off-cut to a desired location

FULL CUT PILE CUTTERS

The pile cutter is fully self-contained and works with any 13–30 ton hydraulic excavator with a hammer line and tiltrotator. It can do full cuts or partial cuts (Cut & Break). Cut quality is excellent due to grabs below and above the blades.

  • Grab the pile and press Start
  • Cut through the pile
  • Release lower grabs
  • Place the off-cut to a desired location
DOWNLOAD BROCHURE